You are here: welcome » dcore » acer_aspire_one_zg5

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
dcore:acer_aspire_one_zg5 [2015/05/17 14:33] – [Suspend] sm8psdcore:acer_aspire_one_zg5 [2016/05/17 15:37] (current) – [Further information] nitram
Line 1: Line 1:
 ====== dCore on Acer Aspire One ZG5 ====== ====== dCore on Acer Aspire One ZG5 ======
-The [[http://en.wikipedia.org/wiki/Acer_Aspire_One|Aspire One ZG5]] is a 8.9-inch netbook from 2008. It features an Atom N270 and 1 GB of RAM.+The [[http://en.wikipedia.org/wiki/Acer_Aspire_One|Aspire One ZG5]] is a 8.9-inch netbook from 2008. It features an Intel 945GSE Express chip set with an Intel Atom N270 and up to 1.5 GB of RAM.
  
 ===== Tested ===== ===== Tested =====
-  * dCore-jessie --- //[[sm8ps-tcl1@yahoo.com|sm8ps]] 201412// +  * dCore-jessie with LXDE --- //[[sm8ps-tcl1@yahoo.com|sm8ps]] 201412// 
-  * ub-dCore-trusty --- //[[sm8ps-tcl1@yahoo.com|sm8ps]] 201505// +  * dCore-trusty with FLWM --- //[[sm8ps-tcl1@yahoo.com|sm8ps]] 201505// 
 +  * dCore-trusty with LXDE --- //[[sm8ps-tcl1@yahoo.com|sm8ps]] 201506//
 ===== Hardware-switch for wireless card ===== ===== Hardware-switch for wireless card =====
 The wireless card can be turned off by a hardware-switch located at the right of the front edge. Be warned about touching that switch, though, as it is impossible to re-activate the card from the running system. That is possible //only// during the boot-phase. The wireless card can be turned off by a hardware-switch located at the right of the front edge. Be warned about touching that switch, though, as it is impossible to re-activate the card from the running system. That is possible //only// during the boot-phase.
Line 28: Line 28:
 <code>echo mem | sudo tee /sys/power/state</code> <code>echo mem | sudo tee /sys/power/state</code>
  
-Seemingly the settings for the touchpad (see below) do not persist across suspension, likely because the X-screen is re-built in a way. Thus the scripts under '~/.X.d/' have to be re-run.+Seemingly the settings for the touchpad (see below) do not persist across suspension, likely because the X-screen is re-built in a way. Most notably two-finger tapping is interpreted as right-click then. Thus the scripts under '~/.X.d/' have to be re-run. 
 + 
 +Embedding this all into a shelll alias can be done through the following line in '~/.ashrc' (add more scripts if applicable). 
 +<code>alias s='echo mem | sudo tee /sys/power/state ; ~/.X.d/synaptics'</code> 
 +The latter command is executed after waking up from suspension. 
 ===== Touchpad ===== ===== Touchpad =====
-The touchpad works with two-finger scrolling out of the box. Due to its minuscule size, "middle-tap" (lower right corner) is quite hard to get right. Therefore I prefer to have two-finger tapping be recoginzed. The following code placed in a file 'synaptics' under '~/.X.d/' does it.+The touchpad works with two-finger scrolling out of the box. Due to its minuscule size, "middle-tap" (lower right corner) is quite hard to get right. Therefore I prefer to have two-finger tapping be recoginzed.  
 + 
 +The following code placed in a file 'synaptics' under '~/.X.d/' does it. Some more options are commented out. The page on Synaptics in the [[https://wiki.archlinux.org/index.php/Touchpad_Synaptics|Archlinux-Wiki]] provides more information about available configuration settings.
  
 <code> <code>
 #!/bin/sh #!/bin/sh
-/usr/bin/synclient VertTwoFingerScroll=1 +#/usr/bin/synclient HorizEdgeScroll=0          
-/usr/bin/synclient HorizTwoFingerScroll=1 +#/usr/bin/synclient VertEdgeScroll=0           
-/usr/bin/synclient RBCornerButton=3 +#/usr/bin/synclient VertTwoFingerScroll=1 
-/usr/bin/synclient RTCornerButton=2+#/usr/bin/synclient HorizTwoFingerScroll=1 
 +#/usr/bin/synclient RBCornerButton=3 
 +#/usr/bin/synclient RTCornerButton=2
 /usr/bin/synclient TapButton1=1 /usr/bin/synclient TapButton1=1
 /usr/bin/synclient TapButton2=2 /usr/bin/synclient TapButton2=2
Line 43: Line 52:
  
 The program 'synclient' is imported through the package ''xserver-xorg-input-synaptics''. The program 'synclient' is imported through the package ''xserver-xorg-input-synaptics''.
-Three-finger tapping does not seem to be recognized on this machine at all.+Three-finger tapping does not seem to be recognized at all on this machine. 
 + 
 +===== Screen back-light ===== 
 +The screen luminosity may be controlled by the keyboard (presumably via ACPI). 
 + 
 +===== Further information ===== 
 +There are numerous Internet pages dedicated to this type of computer that contain tips and tweaks. 
 +  * [[https://wiki.debian.org/DebianAcerOne|Debian wiki]] 
 +  * [[https://cryptojedi.org/misc/aa1.shtml|Blog page for Debian Lenny]] 
 +  * [[https://help.ubuntu.com/community/AspireOne|Ubuntu community page]] 
 +  * [[https://wiki.archlinux.org/index.php/Acer_Aspire_One|Archlinux wiki]] 
 +  * [[http://crunchbanglinux.org/wiki/howto/aspireone|Crunchbang Linux wiki]] 
 + 
 +**[[http://wiki.tinycorelinux.net/dcore:welcome|> Return to the dCore Wiki Welcome page]]**
  
-The page on Synaptics in the [[https://wiki.archlinux.org/index.php/Touchpad_Synaptics|Archlinux-Wiki]] provides more information about available configuration settings. 
Print/export
QR Code
QR Code dcore:acer_aspire_one_zg5 (generated for current page)